一：安裝 NCStudio 軟件。將 NCStudio 系統安裝光盤放入光驅。 雙擊“我的電腦”，打開后再雙擊光驅盤符。待光盤打開后，雙擊運行SETUP.EXE安裝程序。 單擊“下一步”，系統提示選擇安裝的目的地位置。單擊“下一步”，系統提示選擇程序文件夾。單擊“下一步”，系統提示開始復制文件。單擊下一步，系統自動完成文件復制過程。并且提示立即關閉計算機。請選擇立即關閉計算機。在計算機關閉后，開始安裝運動控制卡。

1： Install the ncstudio software. Put the installation CD of ncstudio system into the CD-ROM drive. Double click my computer, open it, and then double-click the drive letter. After the CD is opened, double-click to run SETUP.EXE erection sequence. Click next, and you will be prompted to select the installation destination. Click Next and you will be prompted to select the program folder. Click Next and you will be prompted to start copying files. Click Next and the system will automatically complete the file copy process. And prompt to shut down the computer immediately. Please choose to turn off the computer now. After the computer is turned off, start installing the motion control card.、

二：安裝NCStudio 運動控制卡。關閉主機電源，打開計算機的機箱蓋，將運動控制卡插入插口形式匹配的擴展槽內。安裝運動控制卡時，用手輕按運動控制卡兩側，確保運動控制卡穩固插入槽中，與計算機底板接觸良好、可靠，而且不存在搖晃的情況，然后旋緊板卡的緊固螺釘，蓋好機箱蓋。這樣運動控制卡的安裝就完成了。

2： Install ncstudio motion control card. Turn off the power of the host computer, open the computer case cover, and insert the motion control card into the expansion slot matched with the socket. When installing the motion control card, gently press the two sides of the motion control card to ensure that the motion control card is firmly inserted into the slot, has good and reliable contact with the computer base plate, and does not shake. Then tighten the fastening screw of the card, and finally cover the chassis cover. In this way, the installation of the motion control card is completed.

三：重新啟動計算機。安裝好運動控制卡，請重新啟動計算機。在您重新啟動計算機后， Windows 操作系統就會報告找到新硬件，并自動配置系統，很快這個過程就會結束。 這時整個 NCStudio 軟件和運動控制卡的安裝完成。在桌面上和開始->程序菜單中都有啟動 NCStudio 軟件的快捷方式。此時通過相應的快捷方式即可啟動 NCStudio軟件。

3： Restart the computer. After installing the motion control card, please restart the computer. After you restart your computer, the windows operating system will report that new hardware has been found and the system will be automatically configured, and the process will soon be over. At this time, the installation of ncstudio software and motion control card is completed. There is a shortcut to start the ncstudio software on the desktop and in the start program menu. At this time, you can start ncstudio software through the corresponding shortcut.